top of page
Search

Hail Damage Photo Checklist: Every Photo Your Hail Claim Needs (Free PDF)

1 hour ago
3 min read

Most hail files don't come back because the adjuster missed the damage. They come back because the photos didn't prove it.


A reviewer who has never seen the roof has to follow your photos like a walk-through. If an elevation is missing, a test square has no wide shot, or a hit has nothing for scale, the file stalls.


The fix is simple: shoot every hail claim in the same order, every time. Work the house elevation by elevation, then the roof slope by slope. Here's the hail damage photo checklist we use in the field.


1. Start the File


Every photo set starts by proving where you are.


Risk photo

Address or house number


2. Exterior, Elevation by Elevation


Walk the house in the same direction every time: front, right, rear, then left. On each elevation, repeat the same sequence:


Elevation overview

Gutters and downspouts

Windows, screens, and wraps

Soft metals on that elevation, like AC fins, vents, light fixtures, and the mailbox

Collateral damage, or no damage


That last point matters. Shoot the "no damage" photos too. A front elevation with clean gutters tells the reviewer you checked, and it helps show which direction the storm came from. Put a tape measure or coin next to the biggest dents to show hail size.


3. Roof Details


Before you start working the slopes, document the roof itself. These photos support your estimate and answer the questions reviewers ask first.


Number of roof layers

Drip edge present or not

Shingle gauge, or metal roof gauge on a metal roof

Pitch


4. Roof, Slope by Slope


Work the slopes in the same order as the elevations: front, right, rear, then left. On each slope, repeat this sequence:


Slope overview

Damage, or no damage, on the slope

Test square

Roof components on that slope

Look-alikes or prior repairs, if any


Test Square Photos


Every test square gets the same photo sequence:


Wide: shows where the square is on the slope

Medium: shows the full chalk outline with the slope name and hit count written inside

Close-ups: a minimum of 3 hail impact close-ups, with a tape measure, ruler, or coin for scale


Three close-ups is the minimum, not the goal. Shoot enough to show what makes the hits hail: bruising or mat fracture, granule loss exposing fresh asphalt, and sharp, crisp edges.


Photograph squares that fall short of the threshold too. A front slope with 3 hits matters to the file just as much as a rear slope with 11. Carrier thresholds vary, so always follow the carrier's guideline.


For a full walkthrough, read How to Count Hail Hits in a Test Square.


Roof Components


Document the components on each slope as you work that slope: pipe boots, vents, flashing, exhaust caps, and skylights.


Here's a tip that saves time later: chalk the count next to each component, like "3 pipe boots" or "2 vents." The count shows up in your photos, which makes the file faster to review. And when you sit down to write the estimate, you won't have to guess how many pipe boots were on the rear slope.


Look-Alikes and Prior Repairs


If you see blisters, wear, scuffs, nail pops, or old repairs on a slope, photograph them and note them. It shows the reviewer you looked at everything, and it explains why a slope didn't meet the threshold.


5. Interior, If There's a Leak


If the insured reports water inside:


Each affected room, wide

Ceiling and wall damage, close

Moisture readings with the meter in the photo

The attic above the leak, if accessible


Label Every Photo


A hail file can easily run 100 photos or more. Without labels, the reviewer has to guess. With labels, the file reads itself.


Label every photo with where it is, what it is, and the detail. For example: Rear slope, test square, 9 hail hits, chalk marked.


Common Hail Photo Mistakes


Skipping the "no damage" photos on elevations and slopes

Close-ups with no wide shot to show where they are

Fewer than 3 hail impact close-ups per test square

No scale in the hit photos

Skipping test squares that didn't meet the threshold

Missing layers, drip edge, gauge, or pitch photos

Not counting components slope by slope

Photos out of order or unlabeled


Need help with roof measurements for the estimate? Read our guide on how to measure a roof.



Want this on your phone or in your truck? Download the free Hail Damage Photo Checklist. It's a printable one-page version of this exact sequence, with a slope tally table to record test square hits and component counts on every slope.


Then let Photo Check handle the labeling. Shoot your hail photos, tap a label, and move to the next one. Your photos come out organized, renamed, and ready for your report. Start your free 7-day trial at AdjusterPrep.com.

 
 
 

Comments


FIELD TIPS IN YOU INBOX

Storm - season prep, Xactimate tips and new lessons. No spam.

Thanks for submitting!

  • LinkedIn
  • Facebook
  • TikTok
  • Instagram
  • Pinterest

© 2026 by AdjusterPrep. 

bottom of page